Steep-slope Florida roof eave detail relevant to drip edge and underlayment rules

Florida Building Code Supplement 1: What Changes for Roofs Before Dec 31, 2026

October 26, 2026

On October 13, 2026, the Florida Building Commission approved Supplement 1 to the 9th Edition (2026) Florida Building Code. The 9th Edition takes effect December 31, 2026. Permit applications submitted on or after that date are reviewed under the new edition, including the supplement.

This post is a plain-English walkthrough of the Supplement 1 items that matter most for roofs in Southwest Florida: steep-slope drip edge, steel-deck insulation on commercial assemblies, and two statewide permit rules that local building departments are still implementing. It is educational only. For your address, confirm details with the City of Punta Gorda, Charlotte County, Lee County, Sarasota County or whichever building department covers the parcel.

Questions about a roof that will permit near the December 31 line? Call Shea Roofing LLC at (239) 744-6082.

Where this fits with earlier Dec 31 notes

Mid-October industry notes focused on the 9th Edition itself: coastal fastener rules within 3,000 feet of a saltwater coastline (tighter within 300 feet), metal hip and ridge uplift testing, and steep-slope drip edge. Our Punta Gorda roofing guide already flags the December 31 effective date and those fastener lines. Supplement 1 revises a few Chapter 15 roof sections and writes several Chapter 1 permit rules into the code book.

Steep-slope drip edge (Section 1507.17.9.1)

Supplement 1 revises Section 1507.17.9.1. In the approved text:

  • Drip edge is required at eaves and gables of steep-slope roofs (2:12 and above).
  • Drip edge must be lapped a minimum of 3 inches.
  • Eave drip edges must extend 1/2 inch below the sheathing and at least 2 inches back onto the roof.
  • Drip edge is installed over the underlayment. Self-adhering underlayment that meets ASTM D1970 may go over a primed drip edge flange.
  • Drip edge is mechanically fastened a maximum of 4 inches on center.

For underlayment context, see how the layers of a roof work together. On jobs permitted on or after December 31, 2026, these drip edge details belong in the scope, not as a last-minute field change.

Steel decks and insulation (Section 1519.7)

Supplement 1 revises Section 1519.7 for steel decks. Steel decks must be covered with a roof insulation panel that has its own product approval and is listed in the roofing assembly's product approval. The panels are mechanically fastened using the attachment patterns in that assembly approval and in accordance with RAS 117.

That matters for commercial TPO roofing bids that straddle December 31. An older approval path may not be enough if the insulation panel is not listed with its own approval. We check product approvals when we write the scope. Shea's standard commercial workmanship warranty is 10 years; 20-year coverage is available only with the manufacturer NDL package (manufacturer fee applies). We do not use open-ended commercial warranty wording.

Single-family work under $7,500: what the code says, and what to verify locally

Supplement 1 adds Section 105.2.3, matching Florida Statute 553.79(1)(g). In short, a local government that issues building permits must exempt an owner of a single-family dwelling, or the owner's contractor, from getting a building permit for work valued at less than $7,500 on the owner's property, when the statutory conditions are met.

The exemption does not apply to:

  • Property that is partly or entirely in a flood hazard area as defined by the Florida Building Code
  • Electrical, plumbing, structural, mechanical or gas work on a property with a single-family dwelling

To use it, the owner or contractor must submit a written request to the local enforcement agency with a copy of the contract or other documentation showing the nature and value of the work. A project may not be split to get under the limit. The local government has no legal duty to the owner or contractor for exempted work.

Whether a small roofing repair qualifies for that written-request path is decided by the building department for the parcel, not by the statute alone. The statute excludes "structural" work, and many local departments treat roofing as structural or keep their own repair thresholds. Charlotte County's HB 803 notice describes the $7,500 rule as certain minor interior alterations and points to its existing table (roof repairs under 100 square feet with no truss or rafter work). Do not assume a roofing job under $7,500 can skip a permit in Charlotte, Lee, or Sarasota. Check with your city or county building department before anyone skips a roofing permit.

Five business days on small single-family roofing permits

Supplement 1 also revises Section 105.3.4.1, matching Florida Statute 553.792. When an applicant uses a local government plans reviewer, and the application is complete and sufficient, the local government must approve, approve with conditions, or deny certain permits on an existing single-family dwelling within 5 business days if the value of the work is less than $15,000. Roofing is on that list, along with structural, electrical, mechanical, plumbing and other trades named in the statute.

The clock is statewide law. How each city or county staffs and tracks it can still differ. A complete application matters; incomplete packages do not start the same clock. Check with your city or county building department that will review your permit.

What this means if your roof is on the calendar

  1. Know which code your permit will be reviewed under. Applications on or after December 31, 2026, follow the 9th Edition plus Supplement 1.
  2. Put drip edge and underlayment details in the scope for steep-slope work that will permit under the new edition.
  3. For steel-deck TPO or other low-slope assemblies, confirm the insulation panel has its own product approval and is listed in the assembly approval, with fastening per RAS 117.
  4. Do not assume a small repair skips a permit in Charlotte, Lee or Sarasota. Check the local department, especially on flood-zone parcels and any work a building official may call structural.
  5. For complete small single-family roofing applications under the statutory value line, the five-business-day review clock applies when you use the local plans reviewer; still confirm locally how they receive a "complete" package.

About Shea Roofing LLC

Shea Roofing LLC is a licensed and insured Florida roofing contractor based at 6025 Taylor Rd, Suite #107, Punta Gorda, FL 33950. We have been roofing for over 20 years in Southwest Florida, we are a certified contractor with multiple manufacturers, and we install tile, metal, shingle and flat roofs to the Florida Building Code in force for your permit date.

Frequently Asked Questions

When does the 9th Edition Florida Building Code take effect?

December 31, 2026. Permit applications submitted on or after that date must comply with the 9th Edition, including Supplement 1 approved by the Florida Building Commission on October 13, 2026.

What did Supplement 1 change for steep-slope drip edge?

Section 1507.17.9.1 requires drip edge at eaves and gables of steep-slope roofs (2:12 and above), a minimum 3-inch lap, eave drip edge extending 1/2 inch below the sheathing and at least 2 inches onto the roof, installation over the underlayment (with an ASTM D1970 self-adhering option over a primed flange), and mechanical fastening at a maximum of 4 inches on center.

Why does steel-deck insulation matter for a TPO bid after Dec 31?

Revised Section 1519.7 requires a roof insulation panel over a steel deck that has its own product approval, is listed in the roofing assembly product approval, and is fastened per the assembly's patterns and RAS 117. Assemblies that straddle the effective date should be checked against that path before the bid is locked.

Can I skip a roofing permit in Charlotte, Lee or Sarasota if the job is under $7,500?

Not something we can promise. State law creates a single-family exemption under $7,500 with a written request, but it excludes flood-hazard property and electrical, plumbing, structural, mechanical or gas work, and it bans splitting a project to qualify. Local departments decide how that applies to roofing. Confirm with the building department for the parcel before work starts.

Questions about a roof near the code change?

Call Shea Roofing LLC at (239) 744-6082. We will look at the roof, explain how the permit date affects the scope, and put the details in writing. For Port Charlotte jobs, see also our Port Charlotte page.

Shea Roofing LLC
6025 Taylor Rd, Suite #107, Punta Gorda, FL 33950
(239) 744-6082
Florida License CCC1334196

Back to Blog

Copyright 2026. All rights reserved